Difference between revisions of "Electrical: Access and Replace Keyless Entry"

From 3000GT/Stealth Wiki
Jump to navigation Jump to search
(Created page with "Category:How To Category:Electrical Category:Alarm [[Image:Keyless_Entry_Computer.jpg|thumb|Keyless entry computer from a '95 VR-4. If you look closely you can see...")
 
m (Rebuilt tutorial using improved grammar/structure)
Line 3: Line 3:
 
[[Category:Alarm]]
 
[[Category:Alarm]]
 
[[Image:Keyless_Entry_Computer.jpg|thumb|Keyless entry computer from a '95 VR-4. If you look closely you can see the labeling for the switch for "Set 1" and "Set 2".]]
 
[[Image:Keyless_Entry_Computer.jpg|thumb|Keyless entry computer from a '95 VR-4. If you look closely you can see the labeling for the switch for "Set 1" and "Set 2".]]
 +
__NOTOC__
 +
Keyless entry is a convenient feature that was added to the [[Mitsubishi_3000GT/Dodge_Stealth|Mitsubishi 3000GT/GTO]] and [[Mitsubishi_3000GT/Dodge_Stealth|Dodge Stealth]] in order to allow owners to easily lock and unlock their doors without physically inserting a key.
 +
 +
In order to reprogram or replace the keyless entry system, you will need to access the wireless receiver located behind the rear, driver-side panel near the factory speaker. While the receiver is fairly easy to access, any car audio installation shop should be able to help you reach it as well.
 +
 +
 +
'''Time required''': Approximately 1.5 hours
 +
 +
 +
=== Tools Required ===
 +
* Phillips screwdriver (stubby and standard)
 +
* Socket wrench
 +
** 12mm socket
 +
 +
<br style="clear:both;" />
 +
 +
== Access the Keyless Entry Receiver on a Mitsubishi 3000GT/GTO and Dodge Stealth ==
 
[[Image:Factory_Keyless_Entry_2.jpg|thumb|Factory keyless entry computer in relation to the speaker and seatbelt harness.]]
 
[[Image:Factory_Keyless_Entry_2.jpg|thumb|Factory keyless entry computer in relation to the speaker and seatbelt harness.]]
 +
Contributed by: Lloyd Wihl
 +
 +
# '''Remove the retractable hatch cover''' (if you have one).
 +
# '''Remove the rear seat'''. Pull on the two handles at the forward edge of the seat bottom. This will unlatch it so you can lift out the whole seat bottom. Remove the left side rear seat-back by undoing the two 12mm bolts (located at its base).
 +
# '''Remove the left rear panel'''. Unscrew the rearmost screw on the scuff plate (the plastic strip that sits over the rocker panel). Unscrew the single screw on the cover over the rear seatbelt retractor, and lift off this cover. Remove all the screws holding on the large panel. The only tricky part is getting to the two screws at the rear seatbelt retractor - there is not much space, so you will need a short/stubby-style screwdriver. I used a long Phillips screwdriver bit with a socket and it was easy. You don't need to take off any seatbelts - just let the panel hang with the seatbelt still through it.
 +
 +
<br style="clear:both;" />
 +
 +
== Replace the Keyless Entry Receiver on a Mitsubishi 3000GT/GTO and Dodge Stealth ==
  
−
==Access and Replacement==
 
−
Contributed by: Lloyd Wihl
 
  
−
On the 93-96 vehicles --[[User:Dave57|Dave57]] 09:33, 17 October 2007 (MDT) You need to get to the keyless receiver, which is located behind the rear, left-side (driver's-side) panel, that is, the large panel which surrounds the left rear speaker. The whole procedure will take most people around one and a half hours, including re-assembly. (For those who don't want to do it themselves, any car audio installation shop can easily do it.)
+
# '''Replace or modify the keyless entry receiver'''. The receiver is the large box forward of the speaker. There is a 3-position switch on it marked SET 1 - FIX - SET 2. You will find it easier to access this switch if you remove the receiver from the car body. Move the switch to either SET position (the two SET positions are in case you have two transmitters with different codes), so that the receiver will learn the new code. Press either button on the new transmitter. Move the switch back to FIX, to retain the code. Test the new remote operation - it should work.
 +
# '''Reassemble''', making sure that the antenna connector is snug in the receiver.
  
−
Here's the procedure:
+
<br style="clear:both;" />
−
#Remove the hatch cover.
 
−
#Remove the rear seat as follows:
 
−
#*Pull on the two handles at the forward edge of the seat bottom. This will unlatch it so you can lift out the whole seat bottom. Remove the left side rear seat-back, by undoing the two 12-mm bolts, which are at its base.
 
−
#Remove the left rear panel as follows:
 
−
#*Unscrew the rearmost screw on the scuff plate (the plastic strip that sits over the rocker panel.) Unscrew the single screw on the cover over the rear seatbelt retractor, and lift off this cover. Remove all the screws holding on the large panel. The only tricky part is getting to the two screws at the rear seatbelt retractor - there is not much space, so you will need a short screwdriver. I used a long Phillips screwdriver bit with a socket and it was easy. You don't need to take off any seatbelts - just let the panel hang with the seatbelt still through it.
 
−
#:[[Image:Keyless_Remote.jpg|thumb|Keyless entry remote for a '95]]
 
−
#The receiver is the large box forward of the speaker. There is a 3-position switch on it marked SET 1 - FIX - SET 2. You will find it easier to access this switch if you remove the receiver from the car body. Move the switch to either SET position (the two SET positions are in case you have two transmitters with different codes), so that the receiver will learn the new code. Press either button on the new transmitter. Move the switch back to FIX, to retain the code. Test the new remote operation - it should work.
 
−
#Reassemble everything, making sure that the antenna connector is snug in the receiver. You're done.
 
−
#:[[Image:3KGTRemoteprogrammingw.data link.jpg|thumb|How to Program the 97 +--[[User:Dave57|Dave57]] 09:33, 17 October 2007 (MDT)]]
 
  
 
== Compatibility ==
 
== Compatibility ==
 +
<div style="background-color:#FFCCCC;padding:5px 10px;font-weight:bold;">Note: This section is currently under accuracy review. Please check back for updates soon.</div>
 +
[[Image:Keyless_Remote.jpg|thumb|Keyless entry remote for a '95]]
 +
[[Image:3KGTRemoteprogrammingw.data link.jpg|thumb|How to Program the 97 +--[[User:Dave57|Dave57]] 09:33, 17 October 2007 (MDT)]]
 +
 
By DAVE57
 
By DAVE57
  

Revision as of 18:43, March 22, 2013

Keyless entry computer from a '95 VR-4. If you look closely you can see the labeling for the switch for "Set 1" and "Set 2".

Keyless entry is a convenient feature that was added to the Mitsubishi 3000GT/GTO and Dodge Stealth in order to allow owners to easily lock and unlock their doors without physically inserting a key.

In order to reprogram or replace the keyless entry system, you will need to access the wireless receiver located behind the rear, driver-side panel near the factory speaker. While the receiver is fairly easy to access, any car audio installation shop should be able to help you reach it as well.


Time required: Approximately 1.5 hours


Tools Required[edit]

  • Phillips screwdriver (stubby and standard)
  • Socket wrench
    • 12mm socket


Access the Keyless Entry Receiver on a Mitsubishi 3000GT/GTO and Dodge Stealth[edit]

Factory keyless entry computer in relation to the speaker and seatbelt harness.

Contributed by: Lloyd Wihl

  1. Remove the retractable hatch cover (if you have one).
  2. Remove the rear seat. Pull on the two handles at the forward edge of the seat bottom. This will unlatch it so you can lift out the whole seat bottom. Remove the left side rear seat-back by undoing the two 12mm bolts (located at its base).
  3. Remove the left rear panel. Unscrew the rearmost screw on the scuff plate (the plastic strip that sits over the rocker panel). Unscrew the single screw on the cover over the rear seatbelt retractor, and lift off this cover. Remove all the screws holding on the large panel. The only tricky part is getting to the two screws at the rear seatbelt retractor - there is not much space, so you will need a short/stubby-style screwdriver. I used a long Phillips screwdriver bit with a socket and it was easy. You don't need to take off any seatbelts - just let the panel hang with the seatbelt still through it.


Replace the Keyless Entry Receiver on a Mitsubishi 3000GT/GTO and Dodge Stealth[edit]

  1. Replace or modify the keyless entry receiver. The receiver is the large box forward of the speaker. There is a 3-position switch on it marked SET 1 - FIX - SET 2. You will find it easier to access this switch if you remove the receiver from the car body. Move the switch to either SET position (the two SET positions are in case you have two transmitters with different codes), so that the receiver will learn the new code. Press either button on the new transmitter. Move the switch back to FIX, to retain the code. Test the new remote operation - it should work.
  2. Reassemble, making sure that the antenna connector is snug in the receiver.


Compatibility[edit]

Note: This section is currently under accuracy review. Please check back for updates soon.
Keyless entry remote for a '95
How to Program the 97 +--Dave57 09:33, 17 October 2007 (MDT)

By DAVE57

For some 92 all 93,94,and some 95's Two button The numbers are: FCC ID# E4EG8DA.......OMRON G8D-281M-A As they use on EBAY The receiver for this is Part#MB920442

For some 95 and 97 all 96 Three button The numbers are: FCC ID# E4EG8DA.......OMRON G8D-282M-A As they use on EBAY The receiver for this is Part#MR318453 Note: The two remotes and or receivers above will work in either application

The 95 Spyder also uses the two-button remote with FCC ID# E4EG8DE......OMRON G8D-401M-A1

For some 97 all 98 and all 99 Three button FCC ID# E4EG8DL.......OMRON G8D-494M-A As they use on EBAY The receiver for this is Part#MR318470

These are claimed to work but do not work: OMRON G8D-404M-A Galant OMRON G8D-426M-A OMRON G8D-525M-A GQ43VT6T They also claim this is a 3000gt remote if it is it may be 99. To date I have not seen one car that has this #. Can anyone help out with this?

Note (Dave 57): I took apart a 97 SL that had no receiver, the plug was there. Must have been when they started cutting costs.

You can put the later receiver in the earlier car and it will work all but panic. I'm sure I can run a wire and trigger the alarm with this, but there is no wiring diagram for this circuit in the resources I have. So you would have to use a meter and check the receiver pins while activating panic. Hopefully it is a grounding circuit so the hatchback switch wire would work.

Retrieved from "https://www.3swiki.org/index.php?title=Electrical:_Access_and_Replace_Keyless_Entry&oldid=4827"