Difference between revisions of "Tuning: Adapt DIY Datalogger cable for 91-95"
m (links) |
m (links) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 33: | Line 33: | ||
| R1, R2, R6, R7 || 4x 560 Ohm 1/4w resistor || [https://www.mouser.com/ProductDetail/Yageo/CFR-25JT-52-560R /CFR-25JT-52-560R] | | R1, R2, R6, R7 || 4x 560 Ohm 1/4w resistor || [https://www.mouser.com/ProductDetail/Yageo/CFR-25JT-52-560R /CFR-25JT-52-560R] | ||
|- | |- | ||
| − | | R3, R4, R5 || 3x 4.7k ohm 1/4w resistor|| | + | | R3, R4, R5 || 3x 4.7k ohm 1/4w resistor|| [https://www.mouser.com/ProductDetail/Yageo/CFR-25JT-52-4K7 CFR-25JT-52-4K7] |
|- | |- | ||
| − | | T1 || BC556 / 2N3906 || | + | | T1 || BC556 / 2N3906 || [https://www.mouser.com/ProductDetail/Central-Semiconductor/BC556B BC556B] |
|- | |- | ||
| − | | T2 || BC546/2N3904 || | + | | T2 || BC546/2N3904 || [https://www.mouser.com/ProductDetail/ON-Semiconductor-Fairchild/BC546ABU BC546ABU] |
|- | |- | ||
| J1 || 9 Pol Dsub female || Example | | J1 || 9 Pol Dsub female || Example | ||
| Line 77: | Line 77: | ||
[[File:Cable built.jpg]] | [[File:Cable built.jpg]] | ||
| + | |||
| + | |||
| + | '''Software''' | ||
| + | 91-93 | ||
| + | https://evoscan.com/evoscan-gps-obdii-cables/details/4/1/performance-vehicle-pc-diagnostic-interfaces/mitsubishi/subaru/obdii/can-evoscan-software | ||
| + | $25 | ||
| + | 94-95 | ||
| + | http://www.aktivematrix.com/blog/wp-content/uploads/2010/05/Mitsulogger-2.0-Release-Bugfix2.zip Free | ||
| + | * Also EvoScan | ||
Latest revision as of 21:32, August 16, 2019
91-95 Cars, having a non OBD2 are kinda harder to datalog with most of the commercial readers unless you got a specialized product or a really good and expensive solution, but with this you will be able to log your car and build this cable with less than 20 dollars.
Disclamer, this information is out there, either on DSM forums or the 3si forum, the 94-95 cable is pretty much Gatecrasher idea, not taking credit, just put this so everyone can build one.
You will need:
FTDI Serial to USB cable.
You can buy this locally, ebay, amazon, etc. Just MAKE SURE that this cable uses the FTDI chipset, ask the seller, read the auction, it needs to be detected as a device with a chip from FTDI.
https://www.amazon.com/dp/B00QG83YVC
https://www.ebay.com/itm/USB-to-RS232-Adapter-Cable-2m-6-feet-FTDi-chipset
You can use the Male / Female version, if you switch to the female, make sure that you change the part for the d-sub connector for a male version.
2G ECU (94-95)
| Pos | Description | Mouser # |
|---|---|---|
| R1, R2, R6, R7 | 4x 560 Ohm 1/4w resistor | /CFR-25JT-52-560R |
| R3, R4, R5 | 3x 4.7k ohm 1/4w resistor | CFR-25JT-52-4K7 |
| T1 | BC556 / 2N3906 | BC556B |
| T2 | BC546/2N3904 | BC546ABU |
| J1 | 9 Pol Dsub female | Example |
| - | D-sub housing | Example |
| J2 | 16 pin OBD2 connector | Example |
| - | vero board | Example |
1G ECU (91-93)
| Pos | Description | Mouser # |
|---|---|---|
| D | 1N914 | Example |
| R | 10k ohm 1/4w resistor | Example |
| J1 | 9 Pol Dsub female | Example |
| - | D-sub housing | Example |
| J2 | 12 pin OBD1 connector | Example |
| - | vero board | Example |
Software
91-93
https://evoscan.com/evoscan-gps-obdii-cables/details/4/1/performance-vehicle-pc-diagnostic-interfaces/mitsubishi/subaru/obdii/can-evoscan-software
$25
94-95
http://www.aktivematrix.com/blog/wp-content/uploads/2010/05/Mitsulogger-2.0-Release-Bugfix2.zip Free
- Also EvoScan
